Remplacement du Ressort Tendeur de l'Enrouleur de Plastique

Ces instructions concernent le remplacement du Ressort Tendeur de l'Enrouleur de Plastique Tilmor.

Tools

Équipement de protection individuelle

Clé 7/16"

Clé 3/4"

Douille 3/4"

Clé à cliquet

Clé 9/16"

Douille 9/16"

Clé Dynamométrique

Douille 7/16"

Estimated Time

1 hrs

Before You Begin

WARNING: Before making repairs or adjustments set the parking brake, turn off engine, and remove ignition key. Always disconnect the negative battery cable from the battery when working with electrical components. Always work in a manner that does not put safety at risk!

WARNING: Safety glasses must be worn during installation. Ear (hearing) protection must be worn when using air or power tools.

Installation Notes: Right and left hand orientation referred to in these instructions is determined as if facing forward from the operator station.

Ajuster la tension de la courroie

Remove the tension from the belt by adjusting the tensioner (A) to the lowest position (B).

Retirez le couvercle de la poulie

Remove the seven 1/4” bolts (D) and the seven 1/4” flat washers around the outside perimeter and remove the pulley cover.

Retirer la ceinture

Remove the belt from the pulleys.

Retirer la poulie tendeur

To remove the tensioner pulley (F), remove the 3/8” bolt (E) secured in place by the 3/8” locking flange nut.

Retirer l'assemblage du tendeur

Remove the tensioner assembly by removing the 1/2” locking nut (G) that secures the tensioner to the top cover.

Retirer le ressort de torsion

Remove the 3/8” locking flange nut (I) and 3/8” carriage bolt (J) from the tensioner assembly. Remove the torsion spring (H) from the tensioner assembly.

Installer le ressort de torsion

Position the 3/8” carriage bolt (K) through the tensioner assembly mounting bracket. Ensure that the carriage bolt is centered in the mounting hole.

Position the new torsion spring on to the mounting bracket.

Secure the torsion spring in place using a 3/8” locking flange nut (L). Torque the flange nut to 31 ft-lbs (42 Nm).

Installer l'ensemble tendeur

Position the tensioner in the top cover. Insert the tensioner mounting bolt through the upper mounting hole (M).

Ensure that the torsion spring adjustment handle (N) is placed through the top cover (O).

Secure the tensioner in place with the 1/2” locking flange nut (G). Torque the flange nut to 85 ft-lbs (115 Nm).

Installer la poulie tendeur

Place a 3/8” washer on the 3/8” bolt, followed by the tensioner pulley and another 3/8” washer.

Install the pulley onto the tensioner pulley mount in the center mounting hole (P).

Secure the new tensioner pulley in place using a 3/8” locking flange nut. Torque the 3/8” bolt to 35 ft-lbs (47 Nm).

Vérifier l'alignement de la poulie

Ensure that the tensioner pulley is in line with the idler pulley and the reel drive pulley.

Installer la ceinture

Install the belt, by routing the belt around the pulleys as shown below.

NOTE: The V portion of the belt must be on the plastic winder reel drive pulley (Q).

Ajuster la tension de la courroie

Set the belt tension as required by adjusting the tension adjustment lever.

Installez le couvercle de la poulie

Install the pulley cover (C). Torque the seven 1/4” bolts (D) with 1/4" washers to 100 in-lbs (11 Nm).